Catalog

This Generic Oil & Gas Services Manufacturing Catalog outlines products that can be used in Cementing, Stimulation, Drilling, and Production product service lines.

You can also download this catalog as a pdf.

Table of Contents

Cementing

Dispersants

Dispersants are used to reduce the apparent viscosity of a slurry and improve the total rheology by reducing the friction allowing for easier mixing and displacement of slurry.

CD 3

A complex copolymer (without naphthalene sulfonates), as an effective dispersant/friction reducer for fresh and salt water low to high density cement slurries. Usual application is between 0.25 lbs. /sack to 0.75 lbs. /sack cement. Product to be labeled as to customer’s specification in a 50 lb. bag.

CD 3L

A liquid version of CD 3. Usual application is 10 gallons to 20 gallons product per 10 bbls. of mixing water. Product comes in pails, drums, or totes, labeled as to customer’s specification.

CD 2

A naphthalene sulfonated copolymer as an effective dispersant/friction reducer for fresh and salt water (max 16%) low density cement slurries. Usual application is from 0.5 lb. /sack to 1.5 lb. /sack cement. Product comes in 50 lb. bag, labeled as to customer’s specification.

CD 2L

A liquid version of CD 2. Usual application is 15 gallons/25 gallons product per 10 bbls. of mixing water. Product comes in pails, drums, or totes and labeled as to customer’s specification.

Flow Aids

Flow Aids are blending additives that dramatically improve typical pneumatic equipment’s (loading/unloading lines, elbows, T’s) ability to provide a fluid-like flow for bulk materials; i.e. cement, silica flour, bentonite, Gilsonite, fly ash, and Kol-Seal.

Flow Enhancer

A precipitated silica based powder that should be added to the cement or bulk material before adding any additives. Usual product application is 0.03% to 0.18% by weight of bulk material. Comes in 200 lb. drums or 20 lb. pails.

Cement Suspension Agents

These anti-settling agents are used primarily to hold cement & additives in suspension while cement is setting; i.e. high angle, horizontal wells, and in light weight -high water cement ratios.

SA-10

A high molecular weight cellulose derived suspension additive for cement slurries. It aids in the prevention of solid settling while assisting in the control of free-water leak-off. Usual application is 0.2% to 1.0% by weight of cement.

Cement Defoamers

Defoamers, or anti-foaming agents are applied to reduce the opportunity of foaming due to other additives and mixing water; i.e. salt or sea water. Air entrainment not only impacts slurry density, but also impacts the mechanical pumping operation. Defoamers come in liquid or powder form.

Polymer Defoamer

Liquid, linear polymer in a high purity solvent anti-foamer.

Alcohol Defoamer

Liquid, fatty alcohol based ant-foamer.

Silicon Defoamer

Liquid, silicon emulsion based –antifoamer

Note: Usual application ranges from 0.003 – 0.5 % by weight of cement

Product available in totes, drums, and pails.

Cement Spacers and Washes

Cement spacers and washes are used to separate the cementing slurry from the applicable displacing fluid or completion fluid to prevent contamination, as well as to clean the well bore (casing and well bore walls) during the cementation process, allowing for a better bond to casing and well bore. These special fluids are required to perform the same or better rheology as the cement slurry, work in water based systems, oil base systems, or both.

Adjustable Spacer

A polymer and silica based low viscosity spacer base product that can be adjusted and matched with a surfactant selection to meet well bore and water based drilling fluid needs. Usual application is 0.2% to 1.0% by required weight.

Dual Spacer

A polymer with various silica forms to provide the spacer and wash characteristics required to separate oil base or water based drilling fluids and scour the well bore and casing walls. Usual application is 0.2% to 1.0% by required weight.

Note: available in 50 lb. bags.

Viscosifying Agents

Often assistance in holding cement and spacer solids in suspension is required while meeting the rheology required to provide the cementing , spacing and cleaning of well bore and casing. . These viscosifiers also provide fluid loss control. These viscosifiers complete with viscosifier coupled with a surfactant-suspension package.

VA-W

A polysaccharide in a mineral oil with surfactant-suspension package. Usual application requires 0.5 to 1.0% by weight of cement and, or spacer.

Stimulation

Biocides and, or Bactericides

Microorganisms develop and attack polymeric products in drilling, completion, and stimulation fluids. Additionally, microorganisms come from the various water sources as well. Left untreated, expect corrosion, souring of reservoir, and plugging within the reservoir. These biocides come in various forms including sodium hypochlorite, DNPA, and glutaraldehyde.

Omega 5150

Liquid, a non-ionic, non-emulsifying dazomet product that offers a quick kill with long term preservation downhole. Includes superior control over sulfate and producing bacteria. Product is high temperature and pressure tolerant.

MD 5 and MD 20

Liquid DNPA (di-n-propylamine) product commonly used in bactericide applications. Comes in 5% and 20% concentrations. Kills rapidly and has a short half-life.

MagnaCide 1057

Liquid, 50% glutaraldehyde product. Kills rapidly and commonly used as to wide range of application.

Note: all biocides require prior testing within stimulation fluids as to pH impact and ppm application.

Breakers

Breakers are applied in fracturing fluids to break down or return the crosslinked polymer(s) to a fluid state for flowback and reservoir cleanup, or simply break up the polymer chains developed by crosslinking. Breaker systems include powder forms, delayed and, or in encapsulated or, liquid form.

Low Temp 2%

2% active solution of salts and chlorides. Good for temps at >125F. Usual application 1-4 gal per 1000.

Low Temp 10%

10% active solution of salts and chlorides. Good for temps at > 140F. Usual application 1-4 gal per 1000.

Buffers

Buffers provide for the pH adjustment to meet crosslinking activity requirements. These examples can be formulated to meet specific needs

Buffer 1: High pH, 47% potassium carbonate solution

Buffer 2: High pH, potassium carbonate and potassium hydroxide solution

Buffer 3: High pH, potassium carbonate and potassium hydroxide solution

Buffer 4: High pH, potassium hydroxide solution

Buffer 5: High pH, potassium hydroxide solution

Note: available in totes.

Clay Control

Most of all petroleum reservoirs contain clay minerals; i.e. iron based, sodium based, and aluminum base in various percentages. It is of most importance to protect the water sensitive clays from becoming a damaging threat to permeability via swelling and, or migration. When water, and, or treatment fluid that is not in ionic balance contacts the sensitive clays, the clay absorbs the water, or treatment fluid into the crystalline structure resulting in plugging the pores via swelling. Furthermore, these swollen clay particles may flow thru the produced fluids and settle in other pores that further restrict fluid movement. Temporary clay stabilizers protect from swelling and permanent clay stabilizers protect from swelling and migration. A clay stabilizer becomes permanent when the ionic bond is formed with the clays establishing a crystalline structure de-mobilizing the clay.

CS-50

Liquid, 50% choline chloride, temporary biodegradable clay stabilizer with low toxicity.

CS-70

Liquid, 70% choline chloride, temporary biodegradable clay stabilizer with low toxicity.

CS-Dry-45

Sodium chloride with suspension agent, dry, on toxic, temporary biodegradable clay stabilizer

CS-50MC

Liquid, 50% TMAC, temporary clay stabilizer

CS-WM

Liquid, permanent clay stabilizer, non-toxic, blend of salts and a proprietary compound.

Bio-Frac®

Liquid, permanent clay stabilizer, non-toxic, blend of magnesium, calcium chloride, other compounds and elements.

Note: Products can be used in applications ranging from 1-4 gals per 1000. Recommend testing with fluid system as to crosslink activity. All products are available in bulk or tote packaging.

Crosslinkers

Crosslinkers are chemical agents that are applied to link the polymer chains and create the viscosity required with pump pressure to ‘crack or fracture the rock’. These agents are applied as to polymer, temperature and timing as to meet the required viscosity just prior to entering the rock. Borate based crosslinkers are used at low to mid-range polymer systems and metallic based crosslinkers (i.e.; zirconium, titanium) for high temperature polymer systems.

Borate Based

BXL-20: liquid, 2% borate based

BXL-50: liquid, 5% borate based

BXL-70: liquid, 7% borate based

BXL-100: liquid, 10% borate based

HD-BXL: liquid, delayed borate based

Zirconium Based

Z-Link 3-4: liquid, zirconium base, 5.5% ZrO2

Z-Link 6-7: liquid, zirconium base, 9.8% ZrO2

Z-Link 8-9: liquid, zirconium base, 12.6% ZrO2

Note: all products are available in tote package.

Friction Reducers

Friction reducers are typically safe high-molecular weight polyacrylamide in an oil external emulsion. They can be partially compounded and reacted with other chemicals to yield anionic or cationic products. These are the key to provide high rate pumping with reduction in pressure thru tubing and perforations.

Anionic

FRA-6: environmentally safe high molecular polyacrylamide emulsion, to 225F

FRA-7: environmentally safe high molecular polyacrylamide emulsion, to 325F

FRA-9: environmentally safe high molecular polyacrylamide emulsion, to 325F

Note: using 0.5 to 3 gal per 1000 results up to 70% friction reducer. All products available in totes.

Cationic

FR-C20: cationic copolymer based on acrylamide and a cationic quaternary monomer.

FR-C100: cationic water-soluble polymer emulsion

Note: using 0.5 to 1.0 gal per gal results up to 70% friction reducer. All products are available in totes

Guar Slurries

In stimulation & specifically fracturing, liquid gel concentrates are formulated and provided as the proppant carrier and cross linked to provide the fluid properties to crack the rock and formation. The liquid gel concentrate is pulled from transport or totes, hydrated in a few minutes for a fracturing ‘gel’, buffered and crosslink as to time and temp, breakers added as to time and temp, along with a flow back surfactant, a biocide, scale inhibitors, finally and with proppant on a continuous basis. Previous to LGC’s, frac tanks were ‘gelled’ prior to the service intervention. The use of LGC’s created a new era in safe and efficient frac operations.

Generic Guar Slurry (4 lb. /gal Guar Slurry)

The slurry is a 4 lb. per gallon fast hydrating guar, suspended in a high performance suspension and surfactant package, in a low viscosity, colorless solvent with a very low aromatic content. Product is typically compatible with fresh water, potassium chloride water, sodium and calcium chloride brines. Easily crosslinked with borate based systems and easily broken with the traditional guar/borate systems.

Iron Control

In stimulation treatments, iron hydroxides may precipitate and plug system to well bore. Iron control additives are added to hold the iron in suspension, rather than precipitate. This is accomplished by buffering pH of spent acids to low values.

Fe-Check: liquid, complex iron inhibitor

Iron Control 1: liquid, 50% citric acid

Iron Control 80: liquid, acetic acid based

Note: all products available in totes.

Microemulsion

Micro emulsions are stable emulsions of oil, water, and a surfactant formed without the input of energy (shearing). Application is used to improve the flowback for reservoir clean up.

Flow Aid

A water soluble, nonionic surfactant used for improved fluid recovery, wetting, dispersion, and reduction of surface and interfacial tension in fresh, brackish or heavy brine water systems. Good to temp to 250F.

Note: Available in totes

Foamers

Foaming various fluid systems in stimulation provides for density control for sensitive formations as well as diverter. Foaming fresh water, brine fluids, frac fluids and HCL is a common method of stimulation for specific well bores.

Acid Foamer

A foamer with a high tolerance for contamination with hydrocarbon fluids including low density mixtures of hydrocarbon liquids and diesel. It can be used in water, brines, or acid and is compatible with cationic additives such as permanent clay stabilizers acid foamer can be used in any fluid system, Contains anionic and amphoteric foaming agents

Acid Microemulsion Foamer

A foamer and microemulsion / flow aid combined. Acid microemulsion foamer has a high tolerance for contamination with hydrocarbon fluids including low density mixtures of hydrocarbon liquids and diesel. It can be used in water, brines, or acid and is compatible with cationic additives such as permanent clay stabilizers. It can improve fluid recovery, wetting, dispersion, and reduction of surface and interfacial tension in fresh, brackish or heavy brine water systems.

Production

Corrosion Inhibitors

In any well bore being treated, the iron, steel, and even the treating equipment require protection from corrosion. Based on iron and steel content plus temperature, specific additives are selected.

High Temp Corrosion Inhibitor

High temperature oilfield acid systems. Designed for use in hydrochloric acid and acid mixtures at temperatures from 200 F to 350 F. It is a concentrated cationic blend to provide solubility in acids.

TAM 10

An ethoxylated tallow amine, which is versatile water soluble – oil dispensable, filming corrosion inhibitor. The fatty cationic portion attaches to metal, forming a protecting film against H2S, CO2, etc.

TAM 15

An ethoxylated tallow amine, which is versatile water soluble – oil dispersible, filming corrosion inhibitor. The fatty cationic portion attaches to metal, forming a protecting film against H2S, CO2, etc.

Coffee AC

50% coffee based green corrosion inhibitor used in water wells to temps >80F.

Scale Inhibitors

Scale inhibitors are used to control and or prevent the buildup of scale within the completion system (i.e.; perfs, casing, and tubing). Scale types include, but not limited to, include alkaline earth metal scale deposits; calcium carbonate, calcium sulfate, and barium sulfate,

CSI-7805: concentrated water-soluble, liquid scale inhibitors, application 5-20 ppm

CSI-9802: a water-soluble, liquid scale inhibitor, application 0.1 to 0.5 gal per 1000

SI-1W: winterized version of CSI-7805

SI-2W: winterized version of CSI-9802

Scavengers

Hydrogen sulfide gas is found in petroleum and natural gas. Oil or natural gas is considered ‘sour’ if it has a high percentage of hydrogen sulfide. Natural gas can contain up to 28 percent hydrogen sulfide gas, consequently requires a product to remove it from the well and production lines. Thus the application of an H2S scavenger. Biocides are used in stimulation treatments to prevent the ‘souring’ of the reservoir, but once started; the well requires treatment to combat the presence of H2S-corrrosion.

H2S Scavenger

Blend of amines designed for the effective and environmentally removal of H2S from oil and gas in flow lines or bubble tower applications.

Oxygen in water fluid systems (i.e. produced water, completion fluids, stimulation fluids, completion fluids) promotes corrosion and bacteria growth. These systems require deoxygenation.

Oxygen Scavenger

Blend of biosulfate to be added to the fluid systems to remove oxygen from system.

Packer Fluid

Packer fluid refers to the fluid placed in the annulus (between casing, tubing, and completion packer). This fluid may have thermal properties however must be designed to inhibit against specific corrosion potential due to oxygen, sulfur, and, or carbon dioxide environment.

MV-284

A compound propargyl alcohol & a proprietary product for a high temperature packer fluid package additive to inhibit corrosion.

Drilling and Coil Tubing

Lubricants

Lubricants in drilling (either via rotary, top drive, or downhole motors) are required to reduce torque, drag, stuck pipe, and provide lubricity, specifically in deviated and horizontal well bores. Additionally, with all the stages of frac related drill outs via coil tubing/downhole motors, these products are of high value.

PDS Super L

Liquid lubricant compounded with a nonionic surfactant, and a self-activating gellant providing rapid yield with high gel strength. Product offers the following solutions: reduces pressure required to move tubing, increases tubing life by reducing fatigue failure, corrosion to tubing, casing and surface equipment, helps with cuttings removal, Reduces turbulence by reducing wall friction, reduces metal-to-metal friction, and stabilizes shale formations. Effective in fresh, brine, or oil systems. Application from 5 gal to 10 gal per 1000 gallons. Suggest review in field for best results.

BearNBeads

Liquid lubricant compound with a nonionic surfactant, with fine microporous copolymer beads, resistant to oxidation, reduction, mechanical wear and breakage, suspended in a polymer fluid system. Most effective in fresh, brine, or oil systems. Application from 5 gal to 10 gal per 1000 gallons. Suggest review in field for best results.

TNB 100 Nano Lube

Compounded liquid lubricant, with the application of nanoparticle technology, includes nano beads. Provides lubricity, metal to metal, cutting carrying capacity, and eliminates the need for guar, HEC, slickwater, clay stabilizers and corrosion inhibitors. Application from 0.5% to 3% of system. Suggest review in field for best results.

Note: all products come in totes, drums, and pails.

The information contained in this document is believed to be accurate and reliable to the best of our knowledge at the time this document was prepared. The material is supplied solely for informational purposes only and Magnablend, Inc. makes no guarantees or warranties, either expressed or implied, with respect to the accuracy of this data. It is the responsibility of the user of these products to ensure the completeness and accuracy of such information. Always consult the Material Safety Data Sheet for this product prior to use. All product warranties and guarantees shall be governed by the Standard Terms of Sale.